Refrigerators (Full-Size & Columns)
- Dual-refrigeration diagnostics & temperature drift
- Sealed-system repair (compressor, evap, condenser)
- Fans, dampers, sensors, control boards
- Gaskets, hinges, door alignment & sealing
High-rise kitchens in Downtown, Belltown, and South Lake Union. Waterfront homes in Alki and Ballard. Classic houses on Queen Anne, Capitol Hill, and the Central District. Our Factory Certified & Factory Trained technicians service new and legacy Sub-Zero models with OEM parts and spec-based calibration.
Sub-Zero’s dual-refrigeration, humidity control, and sealed-system design are built to preserve food longer. Our diagnostics isolate the root cause, then we install OEM components and validate performance under real-world load.
System-level testing: refrigeration loop, airflow, sensors, controls.
Preserves designed temperature curves and humidity stability.
Cold-hold, defrost, and door-seal validation with documented results.
You receive the findings in writing along with part numbers and warranty terms.
We service both in-warranty and out-of-warranty Sub-Zero products. OEM parts only. Written warranty on labor and installed components.
We support classic built-ins, integrated columns, PRO stainless, wine, under-counter, and discontinued legacy platforms.
Iconic built-ins with louvered grille. Newer CL-series replaces BI; panel or stainless fronts.
Fully integrated, panel-ready columns and over-and-under units for flush cabinetry.
Full-stainless professional look with glass doors on some variants.
24″ wine storage, beverage centers, refrigerator/freezer drawers.
Older BI and 200/300/500-series platforms, including R12/R134a systems.
Exact scope varies by platform, but every repair is documented and calibrated to spec.
In- and out-of-warranty service. OEM parts only. Written warranty on labor and installed components.
Temperature drift, moisture on gaskets, frost on the back wall, or “sweating” bins — common in waterfront condos (Alki, Ballard) and high-use kitchens.
Evaporator frosting, partial cooling, or noisy starts indicate sealed-system issues — typical on older Classics and heavy-duty kitchens.
Random beeps, error codes, lights but no cooling, or resets during heavy use (holidays, parties) — usually control or sensor related.
Low production, hollow cubes, leaks in the deli drawer, or water tasting “off” — frequent after plumbing changes or long idle periods.
Factory Certified & Trained • OEM parts only • In- & out-of-warranty
Condo tower • elevator scheduling
Symptom: temp drift + ice maker stall.
Diagnosis: fan module & sensor drift. Fix: OEM fan + sensor, calibration.
Older framing • tight kitchen
Symptom: frosting in fresh-food section.
Diagnosis: evap leak. Fix: sealed-system repair, recharge, validation.
Settled frame • hinge wear
Symptom: door not sealing.
Diagnosis: gasket wear + hinge sag. Fix: OEM gasket set, hinge alignment, cold-hold test.
Tight utility closet • shared vent path
Symptom: intermittent warm fridge during parties.
Diagnosis: clogged condenser + fan lag. Fix: condenser service, fan module, calibration.
Dock & elevator window
Symptom: no ice, water at kick panel.
Diagnosis: inlet valve leak. Fix: OEM valve, line check, harvest test.
Open-plan kitchen • high use
Symptom: noisy starts + partial cooling.
Diagnosis: weak compressor. Fix: compressor + drier, evac & charge-by-weight, validation.
50+ neighborhoods • ZIPs: 98101–98199 (includes Downtown, Belltown, SLU, Queen Anne, Ballard, Capitol Hill, and more)
Core cluster covers 98101–98199 (incl. 98146 for White Center).
Yes. We are Factory Certified & Factory Trained for Sub-Zero service in Seattle. We handle both in-warranty and out-of-warranty repairs.
Always. OEM parts only, with a written warranty on labor and components.
Yes. Same-day or next-day appointments are available depending on schedule and parts availability.
Absolutely. We service BI and classic 200/300/500 series, including older refrigerants (R12/R134a) and retrofit options.
Yes. We schedule elevators/docks and follow building rules to keep your appointment on time.
Clear access to the unit, note any error codes, and avoid powering off unless advised.
Yes. After diagnostics we outline cost, expected lifespan, and parts lead times.